![]() Sharp bends damages the cable!ģ - Plug in virgin SSD into the HD cable and secure itĤ - Plug in SATA to USB cable and plug in HD into itĥ - Boot up system use Option key to select HDDĥ - Run OS installer from HDD or UBS OS installer. In addition you don't want to crease the cable where it folds! You want smooth arcs. ![]() In addition you want to place a strip of electricians tape on the uppercase where the cable crosses to help protect it from the rough surface of the uppercase. ![]() Here's the needed part MacBook Pro 15" Unibody (Mid 2012) Hard Drive Cable and here's the guide to follow MacBook Pro 15" Unibody Mid 2012 Hard Drive/IR Sensor Cable Replacement. More likely your slowness is an old or bad SATA cable. The queueing issue is not likely your issue! The queuing issue only becomes a problem when you are running multiple programs and/or open docs asa the same time. A clean OS install sheds this buildup of junk and Migration Assistant will carrier over only the stuff you need.Įven if you don’t do the Migration Assistant right after the install, you can do it later! And don’t forget you can also run it from your TimeMachine backup too! Many clone apps don’t properly setup the drive with the hidden partition in addition all of your old junk is carried over. As it turns out you can also do it from an external drive as well! At the end of the installer it will ask you if you want to migrate your stiff from another system or TimeMachine backup. If you have a SATA to USB adapter or an external drive case to hold your old drive it’s a cake walk!īoot up under either a USB thumb drive which is setup as an OS installer or run the installer from your old drive from the adapter cable. ![]() So I am not sure whether the solution was using Winclone to restore to an internal hard drive (rather than one connected by USB), or whether using Boot Camp Assistant to “prepare” the partition made the difference.Surprisingly you already have the needed tool within the OS installer > Migration Assistant < If you are planning to clone Mac hard drive to SSD, let us take a close look at what is the cloning process all about. I had to disable SIP (which I didn’t need to do when I was restoring via USB). Once up and running, I returned to macOS and used Winclone to restore the old image of my bootcamp over this new partition. So having installed my new SSD into the macbook, I deleted the non-functioning windows partition and this time used the Boot Camp Assistant to make a new partition and install a new version of Windows 10. Last time I upgraded my hard drive I had to reinstall windows from scratch so I really hoped Winclone would make the process easier! Any suggestions what I should try next? I didn’t use sysprep because it’s all the same hardware except for the SSD.įeeling quite defeated. If your Mac has an easily accessible drive bay, physically replace the old hard. Swap Drives: Once the cloning process is complete, shut down your Mac. If your cloning software doesn’t handle this automatically, you might need to clone it separately. Also, Windows on the old drive booted from USB now gives the inaccesible boot device error. Clone Bootable Recovery Partition (Optional): Some Macs have a separate recovery partition. Decided to see if installing the new SSD into the macbook would make a difference (as I understanding booting from USB is not so simple for windows bootcamp) but same “Windows failed to start” error message persists.On rebooting, got past the inaccessible boot device error but after the windows icon loads for a period of time then a black and white “Windows Boot Manager” screen shows “Windows failed to start…” suggesting inserting the windows install disc and repairing windows.I following instructions here to inject drivers successfully.I tested booting from USB - new macOS working fine, windows give inaccessible boot device error.Else the asr command work fine for Big Sur System. This Application is free for one month in test mode and completely operational. I restored the windows image to the new drive connected by USB. The best Application to clone your HDD to a SSD is Carbon Copy Cloner.I used Winclone to create an image, saved to my old SSD.I partitioned the new SSD (with more space for bootcamp than original SSD but same block size) using MS DOS formatting for the bootcamp partition.First I cloned macOS to the new SSD with SuperDuper via USB.I cannot get Windows to run on my new SSD despite following instructions from several posts here. I purchased a larger SSD to upgrade the storage space on my macbook for both macOS and Windows. I am using Winclone 8.2 on my 2012 Macbook Pro, running Mojave 10.14.4 and Bootcamp with Windows 10 installed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |